Compression Fittings

Adjustable Standpipe Elbow

SR-564LL

LL series, light and fashionable design

Connection 1

Technical data & dimensional drawing

Please select connections.

Downloads & CAD

Assembly instructions

Assembly instruction Compression Fittings

CAD

Please select connections.

Accessories & recommendations

Gliss Lubricant 5GP

MO-5GP

Electro-Hydraulic Pre-Assembly Machine VARO

MO-VARO

Pipe Clamp, light series, Complete

RS-DLM

Pre-Installation Stud

SR-592

Show all

LL Couplings SR-540LL - Standpipe Reducer

Compression Fittings EN ISO 8434-1

Screw is not the same screw!

This phrase is especially true for Stainless Steel Pipe Fittings, which depend on the highest security and with little downtime.

The heart of a cutting ring fitting according to EN ISO 8434-1 (DIN 2353) is the cutting ring. In most cases, the specially designed and tested Two edge cutting rings are used, which have shown themselves to be very precise and highly reliable a million times. The cutting ring seals the fully assembled screw in three prominent places.

Important information on technical changes, applications, standards and guidelines

The major advantages are:

Extremely good cut in
High tightness, no rust on the surface
Safe installation
No "set" of the cutting ring

Through the use of surface-coated coupling nuts, the tightening torque reduces up to 35%. Furthermore, a cold welding of stainless steel material is prevented in the thread.

Functional description of the ferrule:

When tightening the nut the cutting ring is guided into the connector plug. The cone directs the cutting edge for increased tightening of the nut into the surface of the pipe. The tube is pushed into the nozzle base, where it can exert a sealing function with appropriate clean preparation. On the other side, the cutting ring is wedged by the pressure of the nut onto the tube. With dynamic load this fit provides additional support. If the tube is exactly perpendicular cut and deburred, three distinctive points can be sealed in the fully assembled fitting.

Schneidringverschraubung, Schneidring, Rohrverschraubung, Hydraulikverschraubung, Fluid

The cutting rings are divided into 3 series:

LL: for compressed air, plastic pipes, laboratory apparatus; especially in the low pressure range up to max. PN 100

L: at larger size pressure loads up to max. PN 315, in the field of measurement and control technology, paper and plastics industry, pharmaceutical industry, aerospace, hydraulic systems and in the paint and coatings industry

S: at high pressure, vibrations and high mechanical. Stresses in heavy machinery, shipbuilding, mining, chemical industry, industrial refrigeration, harbor and lock installations, offshore, petrochemical, usually in the pressure range from 250 up to PN 400 using kegligen screw threads to PN 630th

Through the use of surface-coated coupling nuts, the tightening torque reduces up to 35%. Furthermore, a cold welding of stainless steel material is prevented in the thread.

Pipes: There are seamless, soft annealed stainless steel precision tubes from 1.4571 to DIN EN ISO 1127 tolerance class D4 / T3 its recommended not to use welded tubes: in the area of the weld material structure is modified, resulting in the snipping behavior of the cutting ring changing. However, thin-walled tubes are used for cost reasons, often the cutting ring cannot withstand the pressure during assembly. To ensure the function of the fitting nevertheless, we recommend the use of reinforcing sleeves.

24° Taper Couplings

The directional adjustable 24° sealing cone fittings are stainless and suitable for connection to threaded fittings to DIN 3853 with 24° -Inner cones.

Functionality:

The union nut is rotatably mounted on the neck of a body. The pin is thereby between two semi-circular in cross-section radial grooves of the neck and the nut and then performs the holding function of the taper coupling. The sealing is achieved by the O-ring 24° - Taper couplings in the range of 24° -lnner cone the threaded connector (bore form W to DIN 3861).

Benefits:

Adjustable direction by the rotatable cap nut on the neck
Screwed onto threaded fittings normally provided for cutting ring connections to DIN 3853
Small cross-sectional variation
Easy and quick assembly by tightening distance fixed at low torque
High leakage security by O-ring seal
High load capacity with pressure fluctuations and vibrations in the system
High rip out protection by interlocking construction

24° Weld Fittings

In the 24 ° -Weld nipple fitting the pipe welding side is adjusted depending on the diameter and wall thickness of the pipe dimensions. The seal between the fitting and the welding nipple is an O-ring, which is mounted on the 24 ° cone of the welding nipple.

Area video

Information from our product management about product variants, function and areas of application.

Assembly of a 24° Compression fitting according to EN ISO 8434-1

Observe the generally applicable safety regulations when handling tools and machines. Wear appropriate protective clothing.

Quality Management System

In addition to national and international certifications the company Schwer Fittings is additionally certified regularly by customers. Through our own developments and solutions Schwer Fittings has numerous patents and registered designs. Furthermore, we offer the following certificates to download:

Adjustable Standpipe Elbow SR-564LL

Adjustable Standpipe Elbow